View B101AW03-V1_7871418.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) ( v ) preliminary specifications ( ) final specifications module 10.1 wsvga color tft-lcd with led backlight design model name b101aw03 v1 hw: 0a note ( ) led backlight with driving circuit design customer date checked & approved by date note: this specification is subject to change without notice. approved by date 09/30/2008 prepared by 09/30/2008 nbbu marketing division / au optronics corporation www..net
2 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) contents 1. handling precautions ............................ ................................................... ........... 4 2. general description ............................. ................................................... ............. 5 2.1 general specification.......................... ................................................... ............................ 5 2.2 optical characteristics........................ ................................................... ............................ 6 3. functional block diagram ........................ ................................................... ...... 11 4. absolute maximum ratings ........................ ................................................... ... 12 4.1 absolute ratings of tft lcd module............. ................................................... .............. 12 4.2 absolute ratings of environment ................ ................................................... .................. 12 5. electrical characteristics ...................... ................................................... .......... 13 5.1 tft lcd module................................. ................................................... .......................... 13 5.2 backlight unit ................................. ................................................... ............................... 15 6. signal characteristic........................... ................................................... ............ 16 6.1 pixel format image ............................. ................................................... .......................... 16 6.2 the input data format .......................... ................................................... .......................... 16 6.3 integration interface and pin assignment ....... ................................................... .............. 18 6.4 interface timing ............................... ................................................... ............................. 19 7. connector description........................... ................................................... ......... 22 7.1 tft lcd module................................. ................................................... .......................... 22 8. led driving specification ....................... ................................................... ....... 23 8.1 connector description .......................... ................................................... ........................ 23 8.2 pin assignment ................................. ................................................... ............................ 23 9. vibration and shock test ........................ ................................................... ....... 24 9.1 vibration test ................................. ................................................... ............................... 24 9.2 shock test spec:............................... ................................................... ............................ 24 10. reliability.................................... ................................................... .................... 25 11. mechanical characteristics ..................... ................................................... ..... 26 11.1 lcm outline dimension ......................... ................................................... ..................... 26 11.2 screw hole depth and center position.......... ................................................... ............. 28 12. shipping and package ........................... ................................................... ....... 29 12.1 shipping label format......................... ................................................... ....................... 29 12.2 carton package................................ ................................................... ........................... 30 12.3 shipping package of palletizing sequence...... ................................................... ............ 31 13. appendix: edid description..................... ................................................... .... 32 www..net
3 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) record of revision version and date page old description new description remark 0.1 2008/09/30 all first edition for customer 0.2 2008/12/03 21 panel (led) led power sequence panel (led) led power sequence waveform & parameter updated 0.2 2008/12/03 29 shipping label format shipping l abel format information updated 0.2 2008/12/03 32- edid description edid descript ion addition 0.3 2008/12/26 27 2d drawing (back) 2d drawing (ba ck) updated with rotation 0.3 2008/12/26 32- edid description edid descript ion update for clk spec modify 0.4 2008/01/15 6 rgb color spec rgb color spe from tbd to value definition 0.4 2008/01/15 32- edid description edid descript ion update for clk spec modify 0.5 2008/02/02 27 2d drawing (back) 2d drawing (ba ck) update the shipping label position 0.5 2008/12/03 29 shipping label format shipping l abel format information updated www..net
4 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interf ace connector, be sure not to rotate nor tilt the interface connector of the tft module. 10) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 11) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (iec60950 or ul1950), or be applied ex emption. 12) disconnecting power supply before handling lcd modules, it can prevent electric shock, do not touch the electrode parts, cables, co nnectors and led circuit part of tft module that a led light bar build in as a li ght source of back light unit. it can prevent electrostic breakdown. www..net
5 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) 2. general description b101aw03 v1 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and led backlight system. the scree n format is intended to support the wsvga (1024(h) x 600(v)) screen and 262k colors (rgb 6-bi ts data driver) with led backlight driving circuit. all input signals are lvds interface compa tible. b101aw03 v1 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 255.54 (10.1 w) active area [mm] 222.72 x 125.28 pixels h x v 1024 x 3(rgb) x 600 pixel pitch [mm] 0.2175 (h) x 0.2088 (v) pixel format r.g.b. vertical stripe display mode normally white white luminance (i led =20ma) (note: iled is led current) [cd/m 2 ] 200 typ. (5 points average) 170 min. (5 points average) luminance uniformity 1.25 max. (5 points); 1.6 max (13 points) contrast ratio 400:1 typ; 300:1 min response time [ms] 16 typ / 25 max nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 2.8 max. weight [grams] 190 max. min. typ. max. length 234.5 235.0 235.5 width 142.5 143.0 143.5 physical size without inverter, bracket. [mm] thickness - - 5.2 electrical interface 1 channel lvds glass thickness mm 0.5mm surface treatment anti-glare, hardness 3h support color 262k colors ( rgb 6-bit ) www..net
6 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) temperature range operating storage (non - operating) [ o c] [ o c] 0 to +50 - 20 to +60 rohs compliance rohs compliance 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature) : item symbol conditions min. typ. max. unit note white luminance i led =20ma 5 points average 170 200 - cd/m 2 1, 4, 5. r l horizontal (right) cr = 10 (left) 40 40 45 45 - - degree viewing angle h l vertical (upper) cr = 10 (lower) 10 30 15 35 - - 4, 9 luminance uniformity 5p 5 points - - 1.25 1, 3, 4 luminance uniformity 13p 13 points - - 1.60 2, 3, 4 contrast ratio cr 300 400 - 4, 6 cross talk % 4 4, 7 t r rising - - - t f falling - - - response time t rt rising + falling - 16 25 msec 4, 8 rx 0.558 0.588 0.618 red ry 0.321 0.351 0.381 gx 0.312 0.342 0.372 green gy 0.537 0.567 0.597 bx 0.128 0.158 0.188 blue by 0.093 0.123 0.153 wx 0.283 0.313 0.343 color / chromaticity coordinates white wy 0.299 0.329 0.359 ntsc % cie 1931 - 45 - 4 www..net
7 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) note 1 : 5 points position (ref: active area) 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 note 2 : 13 points position (ref: active area) w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3 : the luminance uniformity of 5 or13 points is defi ned by dividing the maximum luminance values by the minimum test point luminance note 4 : measurement method the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature ch ange during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www..net
8 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. note 7 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd 50 cm photo detector lcd panel field=2 contrast ratio (cr)= brightness on the white state brightness on the black state www..net
9 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) note 8 : definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time inte rval between the 10% and 90% of amplitudes. refer to figure as b elow. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www..net
10 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) note 9 . definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal an d 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the scree n rotated about its center to develop the desired measurement viewing angle. www..net
11 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) 3. functional block diagram the following diagram shows the functional block of the 10.1 inches wide color tft/lcd 40 pin (one ch/connector module) www..net
12 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) 4. absolute maximum ratings an absolute maximum rating of the module is as foll owing: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 4 operation humidity hop 10 90 [%rh] note 4 storage temperature tst -20 +60 [ o c] note 4 storage humidity hst 10 90 [%rh] note 4 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: led specification refer to section 5.2 note 4: for quality performance, please refer to au o iis (incoming inspection standard) . twb=39c operating range storage range www..net
13 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; the power specification are measured under 25 and f rame frenquency under 60hz symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power - 0.50 - [watt] note 1/2 idd idd current - 150 - [ma] note 1/2 i rush inrush current - - 1500 [ma] note 3 vddrp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p note 1 : maximum measurement condition black pattern note 2 typical measurement condition: mosaic pattern note 3 measure condition +5.0v +12.0v vcc r1 47k r2 1k vr1 47k sw1 sw mag-spst 1 2 f1 q3 ao6402 g d2 s d1 d5 d6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 90% 10% vin rising time 0v 3.3v 0.5ms www..net
14 of 34 au optronics corporation product specification b101aw03 v0 (document version : 0.1) 5.1.2 signal electrical characteristics: input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of sn 75lvds82dgg (texas instruments) in detail. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) - 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 - [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform vt h vcm vss www..net
15 of 34 au optronics corporation product specification b101aw01 v0 (document version: 0.4) 5.2 backlight unit led parameter guideline for led driving selection ( ref. remark 1) parameter symbol min typ max units condition led forward voltage v f 4 [volt] (ta=25 ) led forward current i f 20 30 [ma] (ta=25 ) led power consumption p led 2.16 [watt] (ta=25 ) note 1 led life-time n/a 10,000 - - hour (ta=25 ) i f =20 ma note 2 output pwm frequency f pw m 100 200 20k hz duty ratio -- 5 -- 100 % note 1: calculator value for reference i f v f =p note 2: the led life-time define as the estimated time to 50% degradation of initial luminous. note 3: this panel will support lower duty ration at pwm c onditional frequency. the pwm frequency constrain between 100hz to 300hz and a same typical 200hz. th e duty ration will support from 5% to 100% www..net
16 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. 6.2 the input data format: tbd note: output signals from any system shall be low o r high-impedance state when vdd is off. www..net
17 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the typical frequency is 54.2mhz.the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. de display timing this signal is strobed at the fal ling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to rxcl kin . hs horizontal sync the signal is synchronized to rx clkin . note: output signals from any system shall be low o r high-impedance state when vdd is off. www..net
18 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 6.3 integration interface and pin assignment: tbd pin signal description pin signal description 1 nc no connection 21 nc no connection (reserve) 2 avdd powersupply,3.3v(typical) 22 gnd ground 3 avdd powersupply,3.3v(typical) 23 nc no connection (reserve) 4 dvdd ddc 3.3vpower 24 nc no connection (reserv e) 5 nc no connection (reserve) 25 gnd ground C shield 6 scl ddcclock 26 nc no connection (reserve ) 7 sda ddcdata 27 nc no connection (reserve ) 8 rin0- -lvds differential data input(r0-r5,g0) 28 gnd ground C shield 9 rin0+ +lvds differential data input(r0-r5,g0) 29 nc no connection (reserve) 10 gnd ground 30 nc no connection (reserve) 11 rin1- -lvds differential data input(g1-g5,b0-b1) 31 vled_gnd led ground 12 rin1+ +lvds differential data input(g1-g5,b0-b1) 32 vled_gnd led ground 13 gnd ground 33 vled_gnd led ground 14 rin2- -lvds differential data input(b2-b5,hs,vs,de) 34 nc no connection (reserve) 15 rin2+ +lvds differential data input(b2-b5,hs,vs,de) 35 pwm system pwm signal input 16 gnd ground 36 led_en led enable pin(+3v input) 17 clkin- -lvds differential clock input 37 nc no connection (reserve) 18 clkin+ +lvds differential clock input 38 vled led power supply 5v~21v 19 gnd ground 39 vled led power supply 5v~21v 20 nc nc 40 vled led power supply 5v~21v www..net
19 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1024 x 600 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 60 hz clock frequency 1/ t clock 54.8 mhz period t v 650 active t vd 600 vertical section blanking t vb 50 t line period t h 1405 active t hd 1024 horizontal section blanking t hb 381 t clock note : de mode only www..net
20 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www..net
21 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 6.5 power on/off sequence: 6.5.1 panel power sequence vdd power and led on/off sequence is as follows. in terface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. . value parameter min. typ. max. unit t1 0.5 - 10 [ms] t2 30 40 50 [ms] t3 200 - - [ms] t4 10 - - [ms] t5 10 - - [ms] t6 0 - - [ms] t7 10 - - [ms] t8 100 - - [ms] t9 0 16 50 [ms] t10 - - 10 [ms] t11 1000 - - [ms] www..net
22 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer ipex / ipex compatible type / part number ipex 20455-040e-12 mating housing/part number ipex 20453-040t-11 www..net
23 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 8. led driving specification 8.1 connector description it is a intergrative interface and comibe into lvds connector. the type and mating refer to section 7. 8.2 pin assignment ref. to 6.3 www..net
24 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 9. vibration and shock test 9.1 vibration test test spec: test method: non-operation acceleration: 1.5 g frequency: 10 - 500hz random sweep: 30 minutes each axis (x, y, z) 9.2 shock test spec: test spec: test method: non-operation acceleration: 220 g , half sine wave active time: 2 ms pulse: x,y,z .one time for each side www..net
25 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 10. reliability items required condition note temperature humidity bias ta= 40 , 90%rh, 300h high temperature operation ta= 50 , dry, 300h low temperature operation ta= 0 , 300h high temperature storage ta= 60 , 35%rh, 300h low temperature storage ta= -20 , 50%rh, 250h thermal shock test ta=-20 to 60 , duration at 30 min, 100 cycles esd contact : 8 kv air : 15 kv note 1 note1: according to en 61000-4-2 , esd class b: some perf ormance degradation allowed. no data lost . self-recoverable. no hardware failures. remark: mtbf (excluding the led): 30,000 hours with a conf idence level 90% www..net
26 of 34 au optronics corporation product specification b101aw01 v0 (document version: 0.4) 11. mechanical characteristics 11.1 lcm outline dimension: www..net
27 of 34 au optronics corporation product specification b101aw01 v0 (document version: 0.4) www..net
28 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 11.2 screw hole depth and center position: screw hole maximum depth, from side surface = 2.0 m m (see drawing) screw hole center location, from front surface = 2. 8 0.3mm (see drawing) screw torque: maximum 2.5 kgf-cm www..net
29 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 12. shipping and package 12.1 shipping label format: www..net
30 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 12.2 carton package: www..net
31 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 12.3 shipping package of palletizing sequence: www..net
32 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 13. appendix: edid description b101aw03 v1 edid code address function value value value note hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code d2 11010010 210 0b hex, lsb first 31 00110001 49 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 13 00010011 19 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input def. (digital i/p, non-tmds, crgb) 80 10000000 128 15 max h image size (rounded to cm) 16 00010110 2 2 16 max v image size (rounded to cm) 0d 00001101 13 17 display gamma (=(gamma*100)-100) 78 01111000 1 20 18 feature support (no dpms, active off, rgb, tmg blk#1) 0a 00001010 10 19 red/green low bits (lower 2:2:2:2 bits) 66 01100 110 102 1a blue/white low bits (lower 2:2:2:2 bits) 95 1001 0101 149 1b red x (upper 8 bits) 96 10010110 150 1c red y/ higher 8 bits 59 01011001 89 1d green x 57 01010111 87 1e green y 91 10010001 145 1f blue x 28 00101000 40 20 blue y 1f 00011111 31 21 white x 50 01010000 80 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 26 standard timing #1 01 00000001 1 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 www..net
33 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10000 lsb b0 10110000 176 37 pixel clock/10000 usb 13 00010011 19 38 horz active lower 8bits 00 00000000 0 39 horz blanking lower 8bits 40 01000000 64 3a horzact:horzblnk upper 4:4 bits 41 01000001 6 5 3b vertical active lower 8bits 58 01011000 88 3c vertical blanking lower 8bits 19 00011001 25 3d vert act : vertical blanking (upper 4:4 bit) 20 00100000 32 3e horzsync. offset 18 00011000 24 3f horzsync.width 88 10001000 136 40 vertsync.offset : vertsync.width 31 00110001 49 41 horz&vert sync offset/width upper 2bits 00 00000 000 0 42 horizontal image size lower 8bits df 11011111 2 23 43 vertical image size lower 8bits 7d 01111101 125 44 horizontal & vertical image size (upper 4:4 bit s) 00 00000000 0 45 horizontal border (zero for internal lcd) 00 00 000000 0 46 vertical border (zero for internal lcd) 00 0000 0000 0 47 signal (non-intr, norm, no stero, sep sync, neg pol) 18 00011000 24 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f manufacture 41 01000001 65 a 60 manufacture 55 01010101 85 u 61 manufacture 4f 01001111 79 o www..net
34 of 34 au optronics corporation product specification b101aw 01 v0 (document version: 0.4) 62 0a 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 70 00 00000000 0 71 manufacture p/n 42 01000010 66 b 72 manufacture p/n 31 00110001 49 1 73 manufacture p/n 30 00110000 48 0 74 manufacture p/n 31 00110001 49 1 75 manufacture p/n 41 01000001 65 a 76 manufacture p/n 57 01010111 87 w 77 manufacture p/n 30 00110000 48 0 78 manufacture p/n 33 00110011 51 3 79 manufacture p/n 20 00100000 32 7a manufacture p/n 56 01010110 86 v 7b manufacture p/n 31 00110001 49 1 7c 20 00100000 32 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum 50 01010000 80 sum 6144 sum to hex 1800 www..net

▲Up To Search▲

Price & Availability of B101AW03-V1

	To Download B101AW03-V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .